Servo system retrofit for injection molding machines in the USA and Canada

Servo system retrofit for injection molding machines in the USA and Canada

Cut the electricity cost of your old or used injection molding machines. We sell, install and commission Inovance and Techmation servo systems. Typical power savings run from 30% to 80%, depending on your machine, cycle time and material. Minimum 1-year warranty on our servo systems. We ship to any country, send engineers on site and give remote support.

Motor runs only as needed

The servo motor speeds up and slows down with each stage of the cycle, so energy is not wasted while the machine waits or holds.

Less heat in the oil

Less wasted energy usually means the hydraulic oil runs cooler, which can reduce cooling load. Results vary by machine.

Quieter running

Because the motor is not running flat out all the time, many machines run noticeably quieter after the retrofit.

Machine to machine

Machine size, age, pump and motor setup, and how the machine is used all change how much power a servo system can save.

Product cycle time

Long cycles with cooling or holding time give a servo system more chances to save. Very short, fast cycles save less.

Material being processed

The material sets the pressure, speed and cooling time your product needs, and that changes the power the machine uses.

Toggle type

Servo drive for the pump on toggle clamp machines.

Ram type (hydraulic)

Servo systems for hydraulic ram machines.

Vertical type

Servo retrofit for vertical injection molding machines.

Two platen

Servo systems for large two-platen machines.

Two color (double color)

Servo drive for machines with two injection units.

Bakelite

Servo retrofit for bakelite molding machines.

The right system depends on your machine size, pump and motor, and budget. We recommend one after seeing your machine details.

What we do for you

• Sales of Inovance and Techmation servo systems
• Shipping to any country, including the USA and Canada
• Installation on your existing machine, on site by our engineers
• Commissioning and setting up for your product
• Step-up or step-down transformers when your supply voltage is outside 380V to 480V
• Remote support after commissioning
• Operator guidance after commissioning

The exact scope depends on your machine.

What we need from you

Send these on WhatsApp, and we will recommend a servo system and tell you what savings to expect.

• Machine make, model and tonnage (tons)
• Pump and motor rating (HP or kW)
• Your plant's supply voltage (phase to phase; our servo system works on 380V to 480V) and frequency (60 Hz in the USA and Canada)
• Typical product cycle time
• Material you process
• Photos of the machine and its electrical cabinet

Send your machine details

Message us on WhatsApp with the details listed above.

Get a recommendation

We suggest a servo system and tell you what savings to expect for your machine.

Installation and commissioning

Our engineers install the servo system on site and commission it so the machine runs your product properly. Remote support is available afterwards.

What is a servo system retrofit for an injection molding machine?

It is the fitting of a servo motor and drive to an existing injection molding machine, so the hydraulic pump works only as hard as each stage of the cycle needs. It lowers power use without replacing the machine.

How much electricity can a servo system save?

Customers typically save 30% to 80% on power. The exact saving depends on the machine, the product cycle time and the material being processed.

Why does the saving range from 30% to 80%?

Every machine and every product is different. Machine size and condition, cycle time, and the material and its cooling time all change how much a servo system can save.

Do you serve customers in the USA and Canada?

Yes. The Plastic Point supplies Inovance and Techmation servo systems to injection molders in the USA and Canada. We ship to any country, send engineers on site and give remote support. Message us on WhatsApp at +91 9990044101 with your machine details.

Can you ship servo systems to my country?

Yes. We can ship to any country, including the USA and Canada.

Which servo systems do you supply?

We deal in Inovance and Techmation servo systems.

Can servo systems be fitted to old and used machines?

Yes. We sell, install and commission servo systems on old and used injection molding machines. We confirm that a servo system suits your machine before we quote.

Which types of injection molding machines can use a servo system?

We work on all kinds of plastic injection molding machines, including toggle, ram-type (hydraulic), vertical, two-platen, two-color (double color) and bakelite machines.

What supply voltage does the servo system work on?

Our servo system works on 380V to 480V. Tell us your plant's supply voltage and frequency when you send your machine details, and we will confirm a suitable system. If your phase-to-phase voltage is higher than this range, such as 575V or 600V, we use a step-down transformer. If it is lower, such as 208V or 230V, we use a step-up transformer. Either way, the servo system receives a supply within 380V to 480V.

Are there incentives for energy-saving upgrades?

Some utilities, states and provinces run energy-efficiency programs. Ask your utility whether a servo retrofit qualifies. We cannot guarantee eligibility.

Do you give a warranty on servo systems?

Yes. All our servo systems carry a minimum 1-year warranty.

Do you handle installation and commissioning?

Yes. We can send our engineers on site to install and commission the servo system, so one team handles the whole job.

Do you offer remote support?

Yes. We give remote support after commissioning, as well as on-site support by our engineers when needed.

Find out what you can save

Send your machine make, model, tonnage, pump and motor rating, supply voltage, cycle time and material. We will recommend a servo system and tell you what savings to expect.